- Published in Contact us
- Be the first to comment!
Contact us
For all questions you can contact us by writing e-mail This email address is being protected from spambots. You need JavaScript enabled to view it.
For all questions you can contact us by writing e-mail This email address is being protected from spambots. You need JavaScript enabled to view it.
| Mod CNC | Axis | DAC | Channel off inp/out | Channel off Pulse/Dir | Channel off transducer | ADC | channel probe | channel handwheell | |
 |
NC-201М | 3+1 | 4 | 48/32 | - | 3 | - | 1 | 1 |
 |
NC-202 | 3+1 | 1 | 40/24 | 3 | 3 | - | - | 1 |
 |
NC-210/1 | 4+1 | 5 | 32/24 | - | 4 | - | 1 | 1 |
| NC-210/2 | 4+1 | 5 | 64/48 | - | 4 | - | 1 | 1 | |
| NC-220/1 | 4+1 | 5 | 32/24 | 4 | 4 | 4 | 1 | 1 | |
| NC-220/2 | 4+1 | 5 | 64/48 | 4 | 4 | 4 | 1 | 1 | |
| NC-230/2 | 5+1 | 6 | 64/48 | - | 5 | - | 1 | 1 | |
| NC-230/3 | 5+1 | 6 | 96/72 | - | 5 | - | 1 | 1 | |
| NC-230/4 | 5+1 | 6 | 128/96 | - | 5 | - | 1 | 1 | |
 |
NC-301 | 4 | 4 | 32/8- | 4 | 1 | |||
| NC-301/1 | 4 | 4 | 64/32 | 4 | 1 | ||||
| NC-301/2 | 4 | 4 | 96/56 | 4 | 1 | ||||
| NC-302 | 4 | 1 | 16/4 | 4 | 4 | 4 | 1 | ||
| NC-302/1 | 4 | 1 | 48/28 | 4 | 4 | 4 | 1 | ||
| NC-302/2 | 4 | 1 | 80/52 | 4 | 4 | 4 | 1 | ||
 |
NC-310 (max) | 16 | 16 | 80/52 | 16 | 16 | 8 | 4 | 2 |
- 5 process
- Look Ahead
- Teach-in
- Gantry axis
- Master-slave axis control
- Rapid axis positioning
- 8 axis helical/linear interpolation
- Circular interpolation CW
- Circular interpolation CCW
- Helical interpolation
- Dwell at end of block
- Deceleration at end of block
- Selects the interpolation plane
- High level geometric programming
- Continuous operation with automatic speed reduction on corners
- Continuous operation without automatic speed reduction on corners
- Point to point operation
- Constant or variable pitch thread
- Offset disable on profile
- Offset enable on profile (tool left/right to part)
- Inch and metric programming
- Point measure with radius offset
- Measure of hole parameters
- Delta of a theoretical point without radius offset
- Programming of coordinates referred to machine zero (only valid within the block)
- Fixed cycle disable
- Drilling cycle
- Spot-facing cycle
- Deep drilling cycle
- Tapping cycle
- Reaming cycle
- Boring cycle
- Boring cycle with dwell
- Absolute programming
- Incremental programming
- Feed rate expressed as the inverse of the item execution time.
- Feed rate expressed in mm/min or in/min
- Feed rate in mm/rev
- Spindle speed in m/min
- Spindle speed in rev/min
- Polar and cylindrical transformations
- 3D compensations
- 5D transformation with tool orientation
- 4D transformation
- Concatenated transformations
- C-spline interpolation
- NURBS interpolation
- Oscillation functions
- Active reset
- Protection zones 2D/3D
- Quadrant error compensation
- Sag compensation, multidimensional
NC-310 - general-purpose CNC, using for all machines and machines centre. The high-speed bus SSB (Serial Speed Bus) is applied in device to link between the intellectual bench board and the nonintellectual block for control of analogue and digital inputs/outputs. The included principle of an open architecture allows applying the CNC device to the complex objects of control.
Super User
